Measurement of Adhesive Bond Properties Including Damage by Dynamic Mechanical Thermal Analysis of a Beam Specimen

A method to obtain mechanical properties using a bonded (double) cantilever beam (or three point bend) specimen loaded in a manner to produce pure shear in the adhesive layer is reviewed. A revised mathematical solution which allows for easier interpretation of optimum beam dimensions to the one originally developed by Moussiaux, Cardon and Brinson for the static case is presented. An extension of this solution for a fixed/fixed viscoelastic beam under steady state oscillations developed by Li, Dickie and Morman is also discussed. Previous results using a vibrating beam to determine the complex viscoelastic properties of a bonded beam are reviewed. These results demonstrate conclusively that dynamic mechanical thermal analysis (DMTA) measurements discriminate differences in surface treatments and various environmental conditions. New measurements are presented that indicate the DMTA procedure can be used to quantify damage simulated by imbedded flaws in beams. The procedure is also shown to assess the effects of both humidity and corrosive environments on lap specimens. It is suggested that this technique may ultimately provide a method to quantify the amount of hidden damage in an adhesive joint subjected to fatigue, moisture or corrosive environments.     

Phase transitions and dimensional and morphological changes in an “Aluminum Hydroxide-Alumina” system under a shock-wave action

A method is proposed to study the sequence of phase transitions in powdered materials under a shock-wave action. It is shown that the aluminum hydroxide-alumina system has the following sequence of phase transformations under a shock-wave action: bayerite boehmite -Al₂O₃ -Al₂O₃. It is found that there are no transitional high-temperature modifications of alumina. A method is developed for obtaining a submicron alumina powder, which allows obtaining materials with a controlled phase composition, including a thermodynamically stable -modification of Al₂O₃. The specific features of the morphological structure and the phase and structural characteristics of powders after a shock-wave action are considered.Translated from Fizika Goreniya i Vzryva, Vol. 41, No. 1, pp. 110–119, January–February, 2005.     

Li_20对AlN陶瓷低温烧结的影响

利用XRD,SEM和TEM研究了Li2O-CaF2-Y2O3体系在/AlN陶瓷低温烧结中的作用机理,研究发现,添加Li2O的/AlN陶瓷有着更低的收缩开始温度和更大的收缩率,这种收缩来自于含Li玻璃相与CaYAlO4液相的共同作用。在烧结过程中,Li2O不仅改变了AlN烧结过程中的相组成,而且改善了液相的性质。由于Li2O和Al2O3在l 100℃以下反应生成含Li玻璃相,使得AlN开始收缩的温度大为降低。在1 600℃以上,含Li玻璃相分解散失,有利于AlN晶界的纯化,同时,CaYAl3O7向CaYAlO4的转变以及液相CaYAlO4在烧结过程中稳定存在,保证了含Li玻璃相散失后AlN的持续收缩。     

“八五”期间陶瓷窑用耐火材料的新进展

本文综合评述了“八五”期间我国陶瓷窑用耐火材料工业在合成低膨胀耐火材料，优质高档窑具品种，窑体及窑车隔热耐火等方面的研究与开发进展，以及各类优质耐火材料在建筑卫生陶瓷窑，日用陶瓷窑上的成功应用。     

电除尘器绝缘子的设计与选择

根据电除尘器绝缘子的功能、工况条件等特点，分别从材质、外形尺寸等方面介绍了设计和选择的注意事项。为用户合理地选择电除尘器绝缘子提供了帮助。     

从煤矸石制取氯化铝联产橡胶填料的研究

在实验室小试、中试装置上进行了从煤矸石制取氯化铝联产橡胶填料的研究，考察了煤矸石性质、工艺条件等对产品质量的影响，结果发现最佳工艺参数为焙烧温度６００～ｑ００℃．焙烧时间为１５～９０ｍｉｎ．焙烧温度对产品质量影响更为显著，制得结晶氯化铝产品质量达到合格品标准，填料用作橡胶制品填充剂具有较好补强与抗曲性能，其胶片的物理机械性能达到普通橡胶板标准。     

阳极氧化铝的表面参数对硅酮结构的装锒密封胶长期黏结性的影响(连载一)

硅酮密封胶对阳极氧化铝的黏结质量千差万别.影响黏结性的关键因素是铝材表面的封孔程度、氧化层的着色情况、清洁剂的特性以及基材表面清洁与打胶之间允许的时间间隔.由于清洁剂将有机污染物从阳极氧化铝表面去除的效果不同,所以此效果并不和黏结质量有必然联系.据猜测,吸附在阳极氧化铝表面的清洁溶剂会改善基材表面从而提高硅酮胶的黏结性,但这种改善效果会随着清洁溶剂随时间的的挥发而降低.对于给定的溶剂,最佳的黏结效果取决于材料表面的封孔程度.依照ISO 2143酸刻蚀方法测量材料表面的封孔程度,可以预测未着色的阳极氧化铝基材的黏结性.对于着色的阳极氧化铝表面,依照ISO 2931的测试标准,用电相位漂移方法可以用来预测黏结质量.一种控制阳极氧化铝表面的方法被提了出来,此方法是测量不同频率下基材的电阻抗并将它成功地和硅酮密封胶与该材料表面的长期黏接性联系起来.     

Preparation of Silicon Carbide/Aluminum Nitride Ceramics Using Organometallic Precursors

Solid solutions of 2H -SiC/AlN can be prepared at temperatures less than 1600°C by rapid pyrolysis ("hot drop") of mixtures of [(Me₃Si)_0.80((CH₂=CH)MeSi)_1.0(MeHSi)_0.35] _n (VPS) or [MeHSiCH₂] _n (MPCS) with [R₂AlNH₂]₃, where R=Et, i -Bu or simply by slow pyrolysis of the precursor mixture in the case of [Et₂AlNH₂]₃. In contrast, slow pyrolysis of mixtures of VPS or MPCS with [ i -Bu₂AlNH₂]₃ yields a composite of 2 H -AlN and 3 C -SiC at 1600°C, which transforms into a single 2 H -SiC/AlN solid solution on heating to 2000°C. The influences of the nature of the precursor and processing conditions on the structure, composition, and purity of the SiC/AlN materials are discussed.     

氢氧化铝微粉生产过程中晶种分解的研究

晶种分解是种分法生产氢氧化铝微粉的工序，介绍了控制铝酸钠精制液的分解温度、分解时间、搅拌强度等条件并添加特制的高活性晶种做晶种生产优质氢氧化铝微粉的生产过程，并通过对几个月的生产跟踪分析研究，得出氢氧化铝微粉的晶种分解主要与晶种的质量和数量、分解温度、分解时间及搅拌强度等因素有关，这对于进一步完善氢氧化铝微粉的生产工艺起到很大的作用。     

氢氧化镁中微量元素硼硅铝的测定

以盐湖高镁卤水为原料生产的氢氧化镁产品纯度不高,含有部分无机杂质离子,为提高产品质量,改进产品性能,通过实验确定了氢氧化镁中微量元素硼、硅、铝的分光光度测定方法。此方法准确度与精密度较高,测定样品中的硼、硅、铝加标回收率分别为98.3%-101.5%,96.0%-99.3%,96.5%-97.3%,相对标准偏差（n=6）分别为2.06%,2.27%,2.39%,快速、简便、成本低,可作为企业生产的常规检测方法使用。